ANVER Vacuum Material Handling

• ANVER divides small universal vacuum suction cups into three groups based on mounting specifications and style. The Group 1 Fittings shown here are simple barbed fittings that push in from the top of the cup.

• Within each vacuum fitting group, the hardware is interchangeable with all other cups within the group. Any Group 1 fitting will fit any Group 1 cup. It may also fit other cups with similarly sized holes in the cups’ centers. Contact the factory to verify suitability.

• These all-metal, electro-less nickel-plated brass fittings are reusable. Once you buy the cups with fittings you only need to buy replacement rubber cups in the future.

• The cup is simply pressed onto the end of the barbed fitting to hold tight. Replacement takes only a few seconds, and does not require unscrewing the fitting.

• These specific cup fittings are top quality, production grade fittings made by Anver Corp in the USA.

Vacuum Fitting
Part No.

Connection
Thread Size

Hex Size
in.
(mm)

L
Height Added
to Assembly
in.
(mm)

H
Height
in.
(mm)

The BM5 5 mm barbed fitting w/ Captured O-Ring screws right onto the SLSA-1 suspensions

0.31
(8)

The BM10-32 barbed fitting w/ Captured O-Ring can screw right into 10-32 UNF or 5 mm female

The BM6 6mm barbed fitting w/ Captured O-Ring can screw into a variety of fittings (listed below)

M6
(6 mm)
male

0.38
(9.5)

0.20
(5)

0.39
(10.0)

The HS6-18F fitting screws right onto the BM6 fitting and gives you a 1/8″ NPT Female Mount

The HS6-18F-G fitting screws right onto the BM6 fitting and then allows you to screw right into the SLSA-2 Suspensions

The HS6-14F fitting screws right onto the BM6 fitting and then allows you to screw right into the SLSA-3 Suspensions

The HS6-14F-G fitting screws right onto the BM6 fitting and gives you a G1/4″ Female Mount

The HS6-18M fitting screws right onto the BM6 fitting and gives you male 1/8″ mount

0.2
(5)

The HS6-18M-G fitting screws right onto the BM6 fitting and gives you male G1/8″ mount

0.2
(5)

The HS6-14M fitting screws right onto the BM6 fitting and gives you male 1/4″ NPT mount

The HS6-14M-G fitting screws right onto the BM6 fitting and gives you male G1/4″ mount

The B18F Barbed fitting is a 1/8″ female NPT thread

B18F

0.47
(12)

–

The B18F-G Barbed fitting is a G1/8″ female thread and allows you to screw right into the SLSA-2 Suspensions

B18F-G

0.47
(12)

–

The B18M Barbed fitting is a 1/8″ male NPT with a 10–32 UNF inside thread

1/8″
NPT
male

The B18M-G Barbed fitting is a G1/8″ male with a 5 mm female inside thread

G1/8″
male

The HSHN5 fitting is a double male 5 mm thread connector

M5 (5 mm)
male
–
M5 (5 mm)
male

0.09
(2.3)

0.31
(8.0)

0.18
(4.6)

0.45
(11.0)

The HS5-5F fitting is a double female 5 mm thread connector

M5 (5 mm)
female
–
M5 (5 mm)
female

0.17
(4.3)

0.31
(8)

0.43
(11.0)

–

The HS1032-1032F fitting is a double 10-32 UNF thread connector

10-32 UNF
female
–
10-32 UNF
female

0.31
(8)

0.37
(9.5)

–

F5-, F10-, F15-, F20-, F25-

B1.5-5-, B1.5-11-, B1.5-14–, B1.5-16-, B1.5-20-, B1.5-20-, B1.5-22-, B1.5-25-

B2.5-5-, B2.5-7-, B2.5-9-, B2.5-14-, B2.5-18-, B2.5-20-, B2.5-25-