ANVER Vacuum Material Handling

Typical Vacuum Lifters with powered tilt (powered upenders) for handling your tilting needs with ease. Powered tilting action is designed to be stopped at any intermediate angle by one person.

ANVER Vacuum Tilters and Upenders are loaded with safety features and have come to set the standard for safe tilting of loads. Each version has been revised over the years to perform better and last longer. The pads, vacuum generators, frame, controls, hardware, filters, safety features and handlebars etc are all new and improved. Every aspect of the lifters has been redesigned and the latest represent the best Tilters available. 

The Standard and Lightweight Electric-Powered (ET/ETL) and Air-Powered (AT/ATL)  Series Vacuum Lifters/Tilters are designed to significantly reduce the effort of upending heavy loads while providing powerful suction force and 90 degree tilt capability. Built with safety in mind, these lifters/tilters are loaded with protective features including: a VLS System, 9V battery powered vacuum leakage sensor and warning system; an attach/release slide valve with safety lock; and locking knobs on the adjustable vacuum pad, slide assemblies, and crossarms (when applicable). The ET and AT Series Lifters/Tilters are capacity rated at a maximum vacuum level of 24 in. Hg (609.6 mm Hg) with a 4:1 safety factor on vacuum holding (unless otherwise specified).

The dual filter/reservoir assembly, equipped on both electric-powered and air-powered vacuum upenders, offers a clean and reliable vacuum hold in less than ideal environments. Constructed with an ergonomic lifter handlebar, a welded steel lifting frame, and end of beam positioning handles, operators can use this equipment with ease and comfort for a wide range of loads and applications.

*Load weight and depth affect the final angle that the lifter achieves. Consult ANVER for ET/AT loads thicker than 1.18 in. (3cm) and ETL/ATL loads thicker than 2 in. (51mm) due to center of gravity offset.

Note: The unit weight does not include optional accessories.

• VPF-07UP vacuum generator with vacuum gauge and master on/off switch (ET Only)
• EP1001UP vacuum generator with vacuum gauge and master on/off switch (ETL Only)
• Electric actuator with anti-coast brake to provide 90° tilt
• VLS System, 9V battery powered vacuum leakage sensor and warning system
• Re-settable circuit breakers for pump and actuator
• Tilt control pendant with 10 ft. (3.5m) coil cord and pendant holster
• Attach/release slide valve with safety lock
• 4 ft (1.2 m) Power Cord with Twistlock Plug and Receptacle
• Check valve to halt loss of vacuum in case of electrical power failure

• Max. load capacity: 500 – 2000 lbs. (227kg – 907kg) (ET Only); 250 lbs. (113 kg) (ETL Only, unless specified.)
• Power required: 115V/60hz/1ph, and 11-15 amps (ET Only)/11 amps (ETL Only). 15 amp service required for both ET and ETL*
• Tilt speed: 8 sec. (500 lbs./227 kg) for ET and ETL; and 22 sec. (1,000 lbs./454 kg), 22 sec. (1,500 lbs./680 kg), 14 sec. (2,000 lbs./907 kg) for ET Only
• Tilt cycles per hour: 56 (500 lbs./227 kg) for ET and ETL; and 20 (1,000 lbs./454 kg), 20 (1,500 lbs./680 kg), 32 (2,000 lbs./907 kg) for ET Only
• High Performance vacuum pump/motor equipped with thermal sensor to prevent overheating for both ET and ETL; and 100% duty cycle for ETL Only

• APF-07UP vacuum generator with vacuum and pressure gauges (AT Only)
• AL1001UP vacuum generator with vacuum and pressure gauges (ATL Only)
• 3/8 NPT air inlet with locking slide valve
• VLS System, 9V battery powered vacuum leakage sensor and warning system
• Pre-set pressure regulator to allow lifter to be operated on lines with higher supply pressure
• Single-stage Venturi with check valve to halt loss of vacuum from generator in case of air supply failure
• Heavy duty air cylinder to provide 90° tilt
• Flow control valves to control tilt speed
• Handle mounted lever valve for tilt controls
• Attach/release slide valve with safety lock

• Max. load capacity: 500 – 2000 lbs. (227kg – 907kg) (AT Only); 250 lbs. (113 kg) (ATL Only, unless specified.)
• Power required: 90-120 psi; clean, dry compressed air, 10.5 SCFM (297.3 l/min)
• Energy Air Saver, the vacuum controlled valve shuts off the flow of compressed air to the pump when the pre-set level is reached, and consequently the consumption of compressed air is minimized.
• Tilt speed: variable with 100% duty cycle, will not overheat

90° Powered Tilting
Click for Chart

Also Available on Select Models:

90° Powered Tilting
with Manual Rotation

Click to Request More Information