Vacuum Cup Materials

  • The standard materials are TPU and translucent silicone (as noted below each part number).

  • For more information on the materials, Click Here.

Ideal for use on delicate materials such as thin plastic sheets, plastic poly- bags, IV bags, etc. Available in sizes from 0.98 to 2.56 inches (25.0 to 65.0mm)

NOTE: Click on any of the the small thumbnail photos in this chart to enlarge for more detail and specifications.

 

RFQ3D Content CentralTracePartsProduct
Photo

(Click to Enlarge)

ANVER
 Part No.
(Material)

Connection
Thread Size
Static 
Diameter*

in.
(mm)
Compressed
Diameter*

in.
(mm)
Static 
Height*

in.
(mm)
Compressed
Height*

in.
(mm)
Load Capacity
at 24 in. Hg
[2:1 Safety Factor]
lb
(kg)

Pull-Off Capacity
at 18 in. Hg
(457 mm Hg)
[1:1 Safety Factor]

lb
(kg)

Level
Compensator
Suspensions
(Click Image for
More Info)

B3.5 Cups
  

B3.5-25-SIT
(TPU and Translucent Silicone)

N/A0.98
 (25)
1.02
 (26)
1.30
 (33)
0.71
 (18)
1.5
 (0.68 Kg)

3
 (1.36)

ANVER SLSA-2 Series Level Compensator Suspensions

  

B3.5-35-SIT
(TPU and Translucent Silicone)

N/A1.38
 (35)
1.46
 (37)
1.42
 (36)
0.91
 (23)
3.4
 (1.54)
6.8
 (3.08)
ANVER SLSA-2 Series Level Compensator Suspensions
   

B3.5-42-SIT
(TPU and Translucent Silicone)

 N/A1.65
 (42)
1.69
 (43) 
1.81
 (46)
1.06
 (27) 
5
 (2.27) 
10
 (4.54) 
ANVER SLSA-2 Series Level Compensator Suspensions
   

 

B3.5-50-SIT
(TPU and Translucent Silicone)

 N/A1.97
 (50)
2.05
 (52) 
1.89
 (48) 
1.18
 (30) 
5.5
 (2.49) 
11
 (4.99) 
ANVER SLSA-2 Series Level Compensator Suspensions
   

 

B3.5-65-SIT
(TPU and Translucent Silicone)

 N/A2.56
 (65)
2.64
 (67) 
2.40
 (61) 
1.57
 (40) 
13.8
 (6.26) 
27.6
 (12.52) 
ANVER SLSA-2 Series Level Compensator Suspensions
Fittings for B3.5 CupsNotesSuspensions
   50/50-2 FITTING
A-05AG
05AG
(Replaces A-3250002)
32.50.002

The 50/50-2 Fitting uses a 50 Strengthening Ring. The  50/50-2 Fitting allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread.

ANVER SLSA-2 Series Level Compensator Suspensions
Click Here to See More Details of Different Suction Cup and Vacuum Cup Materials

* All cups shown above are similar in size and shape to P-Style cups. The dimensional drawings represent the cup dimensions without a load as given by P-Style. The ‘compressed’ column specifications are important in making sure that everything fits, and represent the actual size of the cup after full compression (being flattened out) on a level load. The bigger the cup the greater the enlargement of the diameter. A lower vacuum level will lessen this compression (or flattening out); however, make sure to leave enough room for the static height of the cup in your design.

 The “G” thread is also known as BSPP, commonly used world-wide for Vacuum Applications.