ANVER Vacuum Material Handling

• ANVER divides small universal vacuum suction cups into three groups based on mounting specifications and style. The Group Two Fittings shown here are those that push in from the bottom, exposing a male thread at the top of the cup.
• Within each vacuum fitting group, the hardware is interchangeable with all other cups within the group. Any Group 2 fitting will fit any Group 2 cup. 
• These all-metal, electro-less nickel-plated brass fittings are reusable. Once you buy the cups with fittings you only need to buy replacement rubber cups in the future.
• The cup is held from the bottom flange of the fitting which is screwed into a female connection above the cup to hold it tight. Replacement takes only a few seconds and requires that you unscrew the fitting, replace the cup, and screw the fitting back on. You can usually do this by hand, by grasping the rubber cup and fitting, and turning. However, should you desire, you can also use a screw driver from below the cup. 
• These specific cup fittings are top quality, production grade fittings made by Anver Corp in the USA.

Vacuum Fitting
Part No.

Thru Hole Dia.
or Thread
in.
(mm)

Hex Size
in.
(mm)

L
Height
 Added to Assembly
in. (mm)

H
Height
in.
(mm)

The HS5 fitting screws right into the SLSA-1 Suspensions without a top nut

HS5

0.11
(2.7)

N/A

0.71
(18)

The HS6 fitting screws right into any of the HS6 fittings below

HS6

0.14
(3.5)

N/A

0.79
(20)

The HS10-32 fitting screws right into the HS1032-1032F fitting below or mounting (also screws into M5 female)

HS10-32

0.10
(2.5)

N/A

0.71
(18)

The HS8 fitting screws right into any 8 mm female fitting or mounting

HS8

0.20
(5.1)

N/A

0.79
(20)

The HS6-18F fitting screws right onto the HS6 fitting and gives you a 1/8″ NPT Female Port

The HS6-18F-G fitting screws right onto the HS6 fitting and then allows you to screw right into the SLSA-2 Suspensions

The HS6-14F fitting screws right onto the HS6 fitting and then allows you to screw right into the SLSA-3 Suspensions

The HS6-14F-G fitting screws right onto the HS6 fitting and gives you a G1/4″ Female Port

The HS6-18M fitting screws right onto the HS6 fitting and gives you male 1/8″ mount

0.2
(5)

The HS6-18M-G fitting screws right onto the HS6 fitting and gives you male G1/8″ mount

0.2
(5)

The HS6-14M fitting screws right onto the HS6 fitting and gives you a male 1/4″ NPT mount

The HS6-14M-G fitting screws right onto the HS6 fitting and gives you male G1/4″ mount

The HSHN5 fitting is a double male 5 mm thread connector

M5 (5 mm)
male
 –
M5 (5 mm)
male

0.09
(2.3)

0.31
(8.0)

0.18
(4.6)

0.45
(11.0)

The HS5-5F fitting is a double female 5 mm thread connector

M5 (5 mm)
female
 –
M5 (5 mm)
female

0.17
(4.3)

0.31
(8)

0.43
(11.0)

–

The HS1032-1032F fitting is a double 10-32 UNF thread connector

10-32 UNF
female
 –
10-32 UNF
female

0.31
(8)

0.37
(9.5)

–

The HS18F fitting screws right into the SLSA-2 Suspensions

The HS18G-18F-G fitting screws right into the SLSA-2 Suspensions

F30-, F35-, F40-, F52-, F60-

B1.5-33-, B1.5-43-, B1.5-53-, B1.5-63

B2.5-32-, B2.5-42-, B2.5-62