Vacuum Cups and Suction Cups
P-Series – BL Multiple Bellows Vacuum Cups and Suction Cups
Vacuum Cup Materials
-
The standard materials are Nitrile and Silicone (as noted below each part number).
- For more information on the materials, Click Here.
For use where longer cup movement is required than is possible with “B” series single bellows cups. Ideal for use where level compensation is desired on irregularly shaped objects, where a vertical offset motion is involved, or for use on curved surfaces, especially in the food industry. Available in sizes from 0.78 to 1.97 inches (20.0 to 50.0mm)
NOTE: Click on any of the the small thumbnail photos in this chart to enlarge for more detail and specifications.
Product Photo (Click to Enlarge) |
ANVER and |
Connection Thread Size |
Static Diameter* in. (mm) |
Compressed Diameter* in. (mm) |
Static Height* in. (mm) |
Compressed Height* in. (mm) |
Load Capacity at 18 in. Hg (457 mm Hg) [2:1 Safety Factor] |
Pull-Off Capacity |
Level |
||||
BL20 Cups | |||||||||||||
N/A | 0.78 (20.0) |
0.82 (21) |
0.91 (23.0) |
0.4 (10.2) |
0.7 lbs (0.32 Kg) |
1.40 |
|||||||
BL20-SIT |
N/A | 0.78 (20.0) |
0.82 (21) |
0.91 (23.0) |
0.4 (10.2) |
0.7 lbs (0.32 Kg) |
1.40 |
||||||
BL20 Cups with 20-30 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
|
BL20-NEO/1PC FIT |
G 1/8″ male M5 female |
0.78 (20.0) |
0.82 (21) |
1.32 (33.6) |
0.8 (20.3) |
0.7 lbs (0.32 Kg) |
1.40 |
|||||
|
BL20-SIT/1PC FIT |
G 1/8″ male M5 female |
0.78 (20.0) |
0.82 (21) |
1.32 (33.6) |
0.8 (20.3) |
0.7 lbs (0.32 Kg) |
1.40 |
|||||
BL20 Cups with 20-30 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
|
BL20-NEO/FIT/SCREEN |
G 1/8″ M5 female | 0.78 (20.0) |
0.82 (21) |
1.19 (30.2) |
0.7 (17.8) |
0.7 lbs (0.32 Kg) |
1.40 |
|||||
|
BL20-SIT/FIT/SCREEN |
G 1/8″ M5 female | 0.78 (20.0) |
0.82 (21) |
1.19 (30.2) |
0.7 (17.8) |
0.7 lbs (0.32 Kg) |
1.40 |
|||||
Fittings for BL20 Cups | Notes | Suspensions | |||||||||||
20-30 FITTING
A-3150196 |
|
||||||||||||
|
|||||||||||||
20-30 STRENGTHENING A-0101084 |
The 20-30 Strengthening Ring is used with the above 20-30 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
20-30 CONNECTION PLATE
A-3150141 |
|
||||||||||||
|
|||||||||||||
20-30 LOCKING SPACER
A-3150140 |
The 20-30 Locking Spacer is used with the above 20-30 Connection Plate. It presses in from the bottom. |
||||||||||||
BL30 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 1.18 (30.0) |
1.21 (30.7) |
1.31 (33.3) |
0.55 (14) |
1.8 lbs (0.82 Kg) |
3.60 |
|||||||
BL30-SIT |
N/A | 1.18 (30.0) |
1.21 (30.7) |
1.31 (33.3) |
0.55 (14) |
1.8 lbs (0.82 Kg) |
3.60 |
||||||
BL30 Cups with 40/30-2/BL30 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL30-NEO/1PC FIT |
G 1/8″ female | 1.18 (30.0) |
1.21 (30.7) |
1.65 (41.9) |
0.92 (23.4) |
1.8 lbs (0.82 Kg) |
3.60 |
||||||
BL30-SIT/1PC FIT |
G 1/8″ female | 1.18 (30.0) |
1.21 (30.7) |
1.65 (41.9) |
0.92 (23.4) |
1.8 lbs (0.82 Kg) |
3.60 |
||||||
BL30 Cups with 40 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL30-NEO/FIT/SCREEN |
G 1/8″ female | 1.18 (30.0) |
1.21 (30.7) |
1.65 (41.9) |
0.92 (23.4) |
1.8 lbs (0.82 Kg) |
3.60 |
||||||
BL30-SIT/FIT/SCREEN |
G 1/8″ female | 1.18 (30.0) |
1.21 (30.7) |
1.65 (41.9) |
0.92 (23.4) |
1.8 lbs (0.82 Kg) |
3.60 |
||||||
Fittings for BL30 Cups | Notes | Suspensions | |||||||||||
A-3250001 |
The 40/30-2/BL30 FITTING uses a Strengthening Ring 40. It allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
STRENGTHENING A-0101085 |
The Strengthening Ring 40 is used with the above 40/30-2/BL30 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
A-3150143 |
The 40 Connection Plate uses a 40 Locking Spacer. It allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
A-3150142 |
The 40 Locking Spacer is used with the above 40 Connection Plate. It presses in from the bottom. |
||||||||||||
BL40 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 1.59 (40.3) |
1.64 (41.5) |
1.65 (41.9) |
0.68 (17.3) |
2.45 lbs (1.11 Kg) |
4.90 |
|||||||
BL40-SIT |
N/A | 1.59 (40.3) |
1.64 (41.5) |
1.65 (41.9) |
0.68 (17.3) |
2.45 lbs (1.11 Kg) |
4.90 |
||||||
BL40 Cups with 40/30-2/BL30 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL40-NEO/1PC FIT |
G 1/8″ female | 1.59 (40.3) |
1.64 (41.5) |
1.96 (49.8) |
1.0 (25.4) |
2.45 lbs (1.11 Kg) |
4.90 |
||||||
BL40-SIT/1PC FIT |
G 1/8″ female | 1.59 (40.3) |
1.64 (41.5) |
1.96 (49.8) |
1.0 (25.4) |
2.45 lbs (1.11 Kg) |
4.90 |
||||||
BL40 Cups with 40 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL40-NEO/FIT/SCREEN |
G 1/8″ female | 1.59 (40.3) |
1.64 (41.5) |
1.96 (49.8) |
1.0 (25.4) |
2.45 lbs (1.11 Kg) |
4.90 |
||||||
BL40-SIT/FIT/SCREEN |
G 1/8″ female | 1.59 (40.3) |
1.64 (41.5) |
1.96 (49.8) |
1.0 (25.4) |
2.45 lbs (1.11 Kg) |
4.90 |
||||||
Fittings for BL40 Cups | Notes | Suspensions | |||||||||||
A-3250001 |
The 40/30-2/BL30 FITTING uses a Strengthening Ring 40. It allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
STRENGTHENING A-0101085 |
The Strengthening Ring 40 is used with the above 40/30-2/BL30 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
A-3150143 |
The 40 Connection Plate uses a 40 Locking Spacer. It allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
A-3150142 |
The 40 Locking Spacer is used with the above 40 Connection Plate. It presses in from the bottom. |
||||||||||||
BL50 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 1.97 (50.0) |
2.03 (51.5) |
2.04 (51.8) |
0.9 (23) |
4.8 lbs (2.18 Kg) |
9.60 |
|||||||
BL50-SIT |
N/A | 1.97 (50.0) |
2.03 (51.5) |
2.04 (51.8) |
0.9 (23) |
4.8 lbs (2.18 Kg) |
9.60 |
||||||
BL50 Cups with 50/50-2 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL50-NEO/1PC FIT |
G 1/8″ female | 1.97 (50.0) |
2.03 (51.5) |
2.48 (62.9) |
1.25 (31.8) |
4.8 lbs (2.18 Kg |
9.60 |
||||||
BL50-SIT/1PC FIT |
G 1/8″ female | 1.97 (50.0) |
2.03 (51.5) |
2.48 (62.9) |
1.25 (31.8) |
4.8 lbs (2.18 Kg) |
9.60 |
||||||
BL50 Cups with 50 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
BL50-NEO/FIT/SCREEN |
G 1/8″ female | 1.97 (50.0) |
2.03 (51.5) |
2.39 (60.7) |
1.25 (31.8) |
4.8 lbs (2.18 Kg) |
9.60 |
||||||
BL50-SIT/FIT/SCREEN |
G 1/8″ female | 1.97 (50.0) |
2.03 (51.5) |
2.39 (60.7) |
1.25 (31.8) |
4.8 lbs (2.18 Kg) |
9.60 |
||||||
Fittings for BL50 Cups | Notes | Suspensions | |||||||||||
50/50-2 FITTING A-05AG 05AG (Replaces A-3250002) 32.50.002 |
The 50/50-2 Fitting uses a 50 Strengthening Ring. The 50/50-2 Fitting allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
The A-05AG-18m-G Fitting is utilized with a Strengthening Ring 50. It allows you to screw into any of the SLSA-2 Suspensions using HS18G-18F-G fitting. |
|||||||||||||
50 STRENGTHENING A-0101086 |
The 50 Strengthening Ring is used with the above 50/50-2 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
50 CONNECTION PLATE
A-3150145 |
The 50 Connection Plate uses a 50 Locking Spacer. The A-3150145 50 Connection Plate allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
A-3150144 |
The 50 Locking Spacer is used with the above 50 Connection Plate. It presses in from the bottom. |
* All cups shown above are identical in size and shape to P-Style’s cups. The dimensional drawings represent the cup dimensions without a load as given by P-Style. The ‘compressed’ column specifications are important in making sure that everything fits, and represent the actual size of the cup after full compression (being flattened out) on a level load. (This difference is negligible in the F series.) The bigger the cup the greater the enlargement of the diameter. A lower vacuum level will lessen this compression (or flattening out); however, make sure to leave enough room for the static height of the cup in your design.
Please Note: Load capacity at 18 in. Hg for all BL-Series Cups.
The “G” thread is also known as BSPP, commonly used world-wide for Vacuum Applications. |
|
|
|