Vacuum Cups and Suction Cups
P-Series – D Deep Vacuum Cups and Suction Cups
Vacuum Cup Materials
-
The standard materials are Nitrile and Silicone (as noted below each part number).
- For more information on the materials, click here.
Ideal for use on curved or irregular surfaces or for lifting across corners and edges. Available in sizes from 0.65 to 2.10 inches (16.5 to 53.0mm).
NOTE: Click on any of the the small thumbnail photos in this chart to enlarge for more detail and specifications.
Product Photo (Click to Enlarge) |
ANVER and |
Connection Thread Size |
Static Dia.* in. (mm) |
Maximum Compressed Dia.* in. (mm) |
Static Height* in. (mm) |
Compressed Height* in. (mm) |
Load Capacity at 24 in. Hg (609.6mm Hg) [2:1 Safety Factor] lb (kg) |
Pull-Off Capacity at 27 in. Hg (685.8mm Hg) [1:1 Safety Factor] lb (kg) |
Level |
||||
D15 Cups | |||||||||||||
N/A |
0.65 |
0.78 |
0.65 (16.5) |
0.49 (12.4) |
1.1 lbs (0.50 Kg) |
2.47 (1.12) |
|||||||
D15-SIT |
N/A | 0.65 (16.5) |
0.78 (20.0) |
0.65 (16.5) |
0.49 (12.4) |
1.1 lbs (0.50 Kg) |
2.47 (1.12) |
||||||
D15 Cups with Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D15-NEO/FITTING |
M5 Male | 0.65 (16.5) |
0.78 (20.0) |
1.01 (25.5) |
0.85 (21.6) |
1.1 lbs (0.50 Kg) |
2.47 (1.12) |
||||||
D15-SIT/FITTING |
M5 Male | 0.65 (16.5) |
0.78 (20.0) |
1.01 (25.5) |
0.85 (21.6) |
1.1 lbs (0.50 Kg) |
2.47 (1.12) |
||||||
Fitting for D15 Cups | Notes | Other Fittings | Suspensions | ||||||||||
BM5 FITTING M5 MALE Replaces 10-15 FITTING A-3107030 31.07.030 01AC |
The BM5 FITTING M5 MALE is an improved 5 mm male fitting with captured O-ring which replaces the older 10-15 FITTING M5 MALE. It allows you to screw directly into any of the SLSA-1 Suspensions. |
||||||||||||
BM10-32 |
The 10-32 Fitting UNF Male is a 10-32 UNF Male fitting. It allows you to screw directly into any of the SLSA-1 Suspensions. Fits all the same cups as the 10-15 Fitting above, but in a 10-32 UNF version. Comes with captured O-ring for a vacuum tight seal. Popular alternate fitting for the North American market. |
||||||||||||
D20 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 0.90 (22.0) |
1.10 (28.0) |
0.50 (13.0) |
0.38 (9.7) |
1.8 lbs (0.82 Kg) |
4.00 (1.8) |
|||||||
D20-SIT |
N/A | 0.90 (22.0) |
1.10 (28.0) |
0.50 (13.0) |
0.38 (9.7) |
1.8 lbs (0.82 Kg) |
4.00 (1.8) |
||||||
D20 Cups with 20-30 Fitting | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | ||||||
D20-NEO/1PC FITTING |
G 1/8″ Male M5 Female |
0.90 (22.0) |
1.10 (28.0) |
0.90 (23.0) |
0.78 (19.8) |
1.8 lbs (0.82 Kg) |
4.00 (1.81) |
||||||
D20-SIT/1PC FITTING |
G 1/8″ Male M5 Female |
0.90 (22.0) |
1.10 (28.0) |
0.90 (23.0) |
0.78 (19.8) |
1.8 lbs (0.82 Kg) |
4.00 (1.81) |
||||||
D20 Cups with 20-30 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D20-NEO/FIT/SCREEN |
G 1/8″ Male M5 Female |
0.90 (22.0) |
1.10 (28.0) |
0.80 (21.0) |
0.68 (17.1) |
1.8 lbs (0.82 Kg) |
4.00 (1.81) |
||||||
D20-SIT/FIT/SCREEN |
G 1/8″ Male M5 Female |
0.90 (22.0) |
1.10 (28.0) |
0.80 (21.0) |
0.68 (17.1) |
1.8 lbs (0.82 Kg) |
4.00 (1.81) |
||||||
Fittings for D20 Cups | Notes | Suspensions | |||||||||||
20-30 FITTING
A-3150196 |
|
||||||||||||
|
|||||||||||||
20-30 STRENGTHENING A-0101084 |
The 20-30 Strengthening Ring is used with the above 20-30 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
20-30 CONNECTION PLATE
A-3150141 |
|
||||||||||||
|
|||||||||||||
20-30 LOCKING SPACER
A-3150140 |
The 20-30 Locking Spacer is used with the above 20-30 Connection Plate. It presses in from the bottom. |
||||||||||||
D30 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 1.30 (32.0) |
1.57 (40.0) |
0.75 (19.0) |
0.53 (13.5) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
|||||||
D30-SIT |
N/A | 1.30 (32.0) |
1.57 (40.0) |
0.75 (19.0) |
0.53 (13.5) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
||||||
D30 Cups with 20-30 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D30-NEO/1PC FITTING |
G 1/8″ Male M5 Female |
1.30 (32.0) |
1.57 (40.0) |
1.12 (28.0) |
0.99 (25.1) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
||||||
D30-SIT/1PC FITTING |
G 1/8″ Male M5 Female |
1.30 (32.0) |
1.57 (40.0) |
1.12 (28.0) |
0.99 (25.1) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
||||||
D30 Cups with 20-30 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D30-NEO/FIT/SCREEN |
G 1/8″ Male M5 Female |
1.30 (32.0) |
1.57 (40.0) |
1.10 (27.0) |
0.93 (23.6) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
||||||
D30-SIT/FIT/SCREEN |
G 1/8″ Male M5 Female |
1.30 (32.0) |
1.57 (40.0) |
1.10 (27.0) |
0.93 (23.6) |
3.1 lbs (1.41 Kg) |
7.00 (3.18) |
||||||
Fittings for D30 Cups | Notes | Suspensions | |||||||||||
20-30 FITTING
A-3150196 |
|
||||||||||||
|
|||||||||||||
20-30 STRENGTHENING A-0101084 |
The 20-30 Strengthening Ring is used with the above 20-30 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
20-30 CONNECTION PLATE
A-3150141 |
|
||||||||||||
|
|||||||||||||
20-30 LOCKING SPACER
A-3150140 |
The 20-30 Locking Spacer is used with the above 20-30 Connection Plate. It presses in from the bottom. |
||||||||||||
D50 Cups | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
N/A | 2.10 (53.0) |
2.40 (61.0) |
1.22 (31.0) |
0.99 (25.1) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
|||||||
D50-SIT |
N/A | 2.10 (53.0) |
2.40 (61.0) |
1.22 (31.0) |
0.99 (25.1) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
||||||
D50 Cups with 50/50-2 Fitting | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D50-NEO/1PC FITTING |
G 1/8″ Female | 2.10 (53.0) |
2.40 (61.0) |
1.60 (40.0) |
1.39 (35.3) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
||||||
D50-SIT/1PC FITTING |
G 1/8″ Female | 2.10 (53.0) |
2.40 (61.0) |
1.60 (40.0) |
1.39 (35.3) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
||||||
D50 Cups with 50 Connection Plate | Connection Thread Size | Static Dia. | Max. Dia. | Static Ht. | Comp. Ht | Load Cap. | Pull-Off Cap. | Suspensions | |||||
D50-NEO/FIT/SCREEN |
G 1/8″ Female | 2.10 (53.0) |
2.40 (61.0) |
1.60 (40.0) |
1.39 (35.1) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
||||||
D50-SIT/FIT/SCREEN |
G 1/8″ Female | 2.10 (53.0) |
2.40 (61.0) |
1.60 (40.0) |
1.39 (35.1) |
9.8 lbs (4.44 Kg) |
22.00 (9.98) |
||||||
Fittings for D50 Cups | Notes | Suspensions | |||||||||||
50/50-2 FITTING A-05AG 05AG (Replaces A-3250002) 32.50.002 |
The 50/50-2 Fitting uses a 50 Strengthening Ring. The 50/50-2 Fitting allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
The A-05AG-18m-G Fitting is utilized with a Strengthening Ring 50. It allows you to screw into any of the SLSA-2 Suspensions using HS18G-18F-G fitting. |
|||||||||||||
50 STRENGTHENING A-0101086 |
The 50 Strengthening Ring is used with the above 50/50-2 Fitting. It simply stretches on and snaps in place. Included with cups which use the one-piece fitting. |
||||||||||||
50 CONNECTION PLATE
A-3150145 |
The 50 Connection Plate uses a 50 Locking Spacer. The A-3150145 50 Connection Plate allows you to screw directly into any of the SLSA-2 Suspensions which have a male G 1/8″ Thread. |
||||||||||||
A-3150144 |
The 50 Locking Spacer is used with the above 50 Connection Plate. It presses in from the bottom. |
* All cups shown above are identical in size and shape to P-Style’s cups. The dimensional drawings represent the cup dimensions without a load as given by P-Style. The ‘compressed’ column specifications are important in making sure that everything fits, and represent the actual size of the cup after full compression (being flattened out) on a level load. (This difference is negligible in the F series.) The bigger the cup the greater the enlargement of the diameter. A lower vacuum level will lessen this compression (or flattening out); however, make sure to leave enough room for the static height of the cup in your design.
The “G” thread is also known as BSPP, commonly used world-wide for Vacuum Applications. |
|