ANVER’s Upender 180° Flipper is a C-frame style lifter that lets one person lift sheets and panels, invert them, inspect the other side, and then place them in jigs for assembly or secondary operations. Featuring two double vacuum suction pads to assure even loading and stress-free handling.
Features:
EP1001 vacuum generator with vacuum gauge and master on/off switch.
Tilt control pendant with 10 ft. coil cord.
Power required: 115V/60hz/1ph/5A. 18 amp service required.
Vacuum pump/motor 4.3 SCFM (121.8 l/min), 1/2 HP; equipped with thermal sensor to prevent overheating and 100% duty cycle.
VLS, 9V battery powered vacuum leakage sensor and warning system.
Resettable circuit breaker for vacuum pump.
Electrical cord with twist lock, male and female receptacles.
Check valve to halt loss of vacuum in case of electrical power failure.
Load placement guides.
Self-balancing lifting shackle
Request For Quote
Lifter Model
EF25M2-36C180
EF25M2-48C180
EF25M2-60C180
EF25M2-72C180
EF25M2-84C180
Rated Load Capacity [lbs (kg.)]
250 (113)
250 (113)
250 (113)
250 (113)
250 (113)
Unit Weight [lbs (kg.)]
178 (81)
183 (83)
188 (86)
193 (88)
198 (90)
A Pad Distances Max. [in. (mm)]
43 (1092)
55 (1397)
67 (1701)
79 (2006)
91 (2311)
A Pad Distances Min. [in. (mm)]
28 (712)
28 (712)
28 (712)
28 (712)
28 (712)
B Beam Length [in. (mm)]
36 (914)
48 (1219)
60 (1524)
72 (1829)
84 (2134)
C Pad Dimension [in. (mm)]
9.25 (235)
9.25 (235)
9.25 (235)
9.25 (235)
9.25 (235)
D Maximum Lifter Headroom [in. (mm)]
47 (1194)
47 (1194)
47 (1194)
47 (1194)
47 (1194)
Maximum Load Length x Width [ft. (M)]
5 x 4 (1.5 x 1.2)
6 x 4 (1.8 x 1.2)
8 x 4 (2.4 x 1.2)
10 x 4 (3.0 x 1.2)
12 x 4 (13.7 x 1.2)
Maximum Load Thickness [in. (mm)]
1 (25.4)
1 (25.4)
1 (25.4)
1 (25.4)
1 (25.4)
Pad Number
VP92
VP92
VP92
VP92
VP92
Powered Vacuum Lifters for One-Person Flipping of Loads Air Powered Vacuum Lifter with 180° Powered Flip Made in the USA!
ANVER’s Upender 180° Flipper is a C-frame style lifter that lets one person lift sheets and panels, invert them, inspect the other side, and then place them in jigs for assembly or secondary operations. Featuring two double vacuum suction pads to assure even loading and stress-free handling.
Features:
AL1001UP vacuum generator with vacuum and pressure gauges
3/8 NPT air inlet with locking slide valve
VLS System, 9V battery powered vacuum leakage sensor and warning system
Pre-set pressure regulator to allow lifter to be operated on lines with higher supply pressure
Single-stage Venturi with check valve to halt loss of vacuum from generator in case of air supply failure
Energy Air Saver, the vacuum controlled valve shuts off the flow of compressed air to the pump when the pre-set level is reached, and consequently the consumption of compressed air is minimized.
Tilt speed: variable with 100% duty cycle, will not overheat
Request For Quote
Lifter Model
AF25M2-36C180
AF25M2-48C180
AF25M2-60C180
AF25M2-72C180
AF25M2-84C180
Rated Load Capacity [lbs (kg.)]
250 (113)
250 (113)
250 (113)
250 (113)
250 (113)
Unit Weight [lbs (kg.)]
178 (81)
183 (83)
188 (86)
193 (88)
198 (90)
A Pad Distances Max. [in. (mm)]
43 (1092)
55 (1397)
67 (1701)
79 (2006)
91 (2311)
A Pad Distances Min. [in. (mm)]
28 (712)
28 (712)
28 (712)
28 (712)
28 (712)
B Beam Length [in. (mm)]
36 (914)
48 (1219)
60 (1524)
72 (1829)
84 (2134)
C Pad Dimension [in. (mm)]
9.25 (235)
9.25 (235)
9.25 (235)
9.25 (235)
9.25 (235)
D Maximum Lifter Headroom [in. (mm)]
47 (1194)
47 (1194)
47 (1194)
47 (1194)
47 (1194)
Maximum Load Length x Width [ft. (M)]
5 x 4 (1.5 x 1.2)
6 x 4 (1.8 x 1.2)
8 x 4 (2.4 x 1.2)
10 x 4 (3.0 x 1.2)
12 x 4 (13.7 x 1.2)
Maximum Load Thickness [in. (mm)]
1 (25.4)
1 (25.4)
1 (25.4)
1 (25.4)
1 (25.4)
Pad Number
VP92
VP92
VP92
VP92
VP92
Powered Vacuum Lifters for One-Person Flipping of Loads – Four Pad
ANVER’s Upender 180° Flipper is a C-frame style lifter that lets one person lift sheets and panels, invert them, inspect the other side, and then place them in jigs for assembly or secondary operations. Featuring four double vacuum suction pads to assure even loading and stress-free handling.
Features:
VPE1-GEN3 vacuum generator with vacuum control module, vacuum gauges and vacuum leakage sensor and warning system.
Attach/Release Pendant with Tilt Controls & Safety Lock-Out.
Power required: 120V/1PH/60HZ, 20 Amps.
Vacuum pump/motor 4.3 SCFM (121.8 l/min), 1/2 HP; equipped with thermal sensor to prevent overheating and 100% duty cycle.
Resettable circuit breaker for vacuum pump.
Electrical cord with twist lock, male and female receptacles.
Check valve to halt loss of vacuum in case of electrical power failure.
Heavy duty helical worm gearbox and motor.
Three position lifting shackle.
Request For Quote
Lifter Model
EF50M4-86C180-2/44
Rated Load Capacity [lbs (kg.)]
500 (227)
Unit Weight [lbs (kg.)]
1050 (476)
A Pad Distances Max. [in. (mm)]
94 (2387)
A Pad Distances Min. [in. (mm)]
40 (1016)
B Beam Length [in. (mm)]
86 (2184)
C Pad Dimension [in. (mm)]
9.13 (232)
D Crossarm Length [in. (mm)]
44 (1123)
E Pad Distances Along Crossarm Max. [in. (mm)]
49 (1244)
E Pad Distances Along Crossarm Min. [in. (mm)]
24 (610)
F Handlebar Length [in. (mm)]
53 (1346)
G Handlebar Height Max. [in. (mm)]
52 (1321)
G Handlebar Height Min. [in. (mm)]
22 (559)
H Maximum Lifter Headroom [in. (mm)]
81 (2058)
Maximum Load Length x Width [ft. (M)]
12 x 6 (3.6 x 1.8)
Maximum Load Thickness [in. (mm)]
1.25 (31)
Pad Number
VP92
13600169 A
Powered Vacuum Lifters for One-Person Flipping of Loads – Twelve Pad
ANVER’s Upender 180° Flipper is a C-frame style lifter that lets one person lift sheets and panels, invert them, inspect the other side, and then place them in jigs for assembly or secondary operations. Featuring twelve double vacuum suction pads to assure even loading and stress-free handling.
Features:
VPE1-GEN3 vacuum generator with vacuum control module, vacuum gauges and vacuum leakage sensor and warning system.
Attach/Release Pendant with Tilt Controls & Safety Lock-Out.
Power required: 120V/1PH/60HZ, 20 Amps.
Vacuum pump/motor 4.3 SCFM (121.8 l/min), 1/2 HP; equipped with thermal sensor to prevent overheating and 100% duty cycle.
Resettable circuit breaker for vacuum pump.
Electrical cord with twist lock, male and female receptacles.
Check valve to halt loss of vacuum in case of electrical power failure.
Heavy duty helical worm gearbox and motor.
Three position lifting shackle.
Request For Quote
Lifter Model
EF80M12-166C180-6/44
Rated Load Capacity [lbs (kg.)]
800 (362)
Unit Weight [lbs (kg.)]
1140 (517)
A Pad Distances Max. [in. (mm)]
174 (4419)
A Pad Distances Min. [in. (mm)]
79 (1998)
B Beam Length [in. (mm)]
166 (4216)
C Pad Dimension [in. (mm)]
9.25 (235)
D Crossarm Length [in. (mm)]
44 (1123)
E Pad Distances Along Crossarm Max. [in. (mm)]
49 (1244)
E Pad Distances Along Crossarm Min. [in. (mm)]
24 (610)
F Handlebar Length [in. (mm)]
72 (1829)
G Handlebar Height Max. [in. (mm)]
43 (1092)
G Handlebar Height Min. [in. (mm)]
22 (559)
H Maximum Lifter Headroom [in. (mm)]
81 (2058)
Maximum Load Length x Width [ft. (M)]
16 x 6 (4.8 x 1.8)
Maximum Load Thickness [in. (mm)]
1 (25)
Pad Number
VP92
13600168 A
Custom Powered Vacuum Lifters with Powered 180° Flipping-Upending For One-Person Load Manipulation
ANVER offers custom vacuum lifters with powered 180 degree flipping/upending for easy one-person load manipulation.
ANVER’s Upender 180° Flipper is a C-frame style lifter that lets one person lift sheets and panels, invert them, inspect the other side, and then place them in jigs for assembly or secondary operations. Featuring eight double spring-loaded vacuum suction pads to assure even loading and stress-free handling, this inverter uses clean electric worm gear drive actuators.
Contact ANVER for more information regarding vacuum lifting and tilting end effectors, or fill out a Lifter Info/Quote Request Form and a Sales Engineer will respond to your request shortly.
