ANVER Vacuum Material Handling

EV200M8-110X44

EV200M8-110X44-1

Vertical Lift
Click for Chart

This lightweight Electric-Powered Vertical Vacuum Lifter is designed to significantly reduce the effort of lifting vertical loads while providing powerful suction force. Built with safety in mind, these lifters are loaded with protective features including: a VLS, 9V battery powered vacuum leakage sensor and warning system; an attach/release pendant; and locking knobs on the adjustable vacuum pad, slide assemblies. Rated at a maximum vacuum level of 24 in. Hg (609.6 mm Hg) at sea level with a 4:1 safety factor on vacuum holding (unless otherwise specified).

Features:

• EP1001 vacuum generator with vacuum gauge.
• Vacuum attach/release pendant control.
• Power required: 115V/60hz/1ph/5A. 15 amp service required.
• Vacuum pump/motor 4.3 SCFM (121.8 l/min), 1/2 HP; equipped with thermal sensor to prevent overheating and 100% duty cycle.
• VLS, 9V battery powered vacuum leakage sensor and warning system.
• Resettable circuit breaker for vacuum pump.
• Electrical cord with twist lock, male and female receptacles.
• Check valve to halt loss of vacuum in case of electrical power failure.
• Removeable leg extensions for handling a variety of load sizes.
• Lifter can be broken down to ship in a smaller package.

Lifter Shown with Leg Extensions

Lifter Shown without Leg Extension
(Shipped in this position for export crate)

AVL25M2-36MR

EVL25M2-24MR

Vertical Lift & Rotation
Click for Chart

The lightweight Electric-Powered (EVL) and Air-Powered (AVL) Vertical Vacuum Lifters are designed to significantly reduce the effort of lifting vertical loads while providing powerful suction force. Built with safety in mind, these lifters are loaded with protective features including: a VLS, 9V battery powered vacuum leakage sensor and warning system; an attach/release slide valve with safety lock (EVL-Series Only); and locking knobs on the adjustable vacuum pad, slide assemblies, and crossarms (when applicable). The EVL and AVL Series Lifters are capacity rated at a maximum vacuum level of 24 in. Hg (609.6 mm Hg) at sea level with a 4:1 safety factor on vacuum holding (unless otherwise specified).

Constructed with an ergonomic lifter handlebar and welded steel lifting frame, operators can use this equipment with ease and comfort for a wide range of loads and applications.

*Load weight and depth affect the final angle that the lifter achieves. Consult ANVER for loads thicker than 2 in. (51mm) due to center of gravity offset.

Note: The unit weight does not include optional accessories.

Electric Powered EVL-Series

Features

• EP1001 vacuum generator with vacuum gauge and master on/off switch
• Power required: 115V/60hz/1ph/5A. 15 amp service required.
• Vacuum pump/motor 4.3 SCFM (121.8 l/min), 1/2 HP; equipped with thermal sensor to prevent overheating and 100% duty cycle
• VLS, 9V battery powered vacuum leakage sensor and warning system
• Resettable circuit breaker for vacuum pump.
• Electrical cord with twist lock, male and female receptacles
• Check valve to halt loss of vacuum in case of electrical power failure

Air Powered AVL-Series

Features

• AL1001 vacuum generator with vacuum and pressure gauges and attach/release switch mounted on the enclosure.
• Power required: 90psi; clean, dry compressed air, 6.1 SCFM (172.7 l/min)
• 3/8 NPT air inlet with locking slide valve, 100% duty cycle.
• VLS, 9V battery powered vacuum leakage sensor and warning system
• Pre-set pressure regulator to allow lifter to be operated on lines with higher supply pressure
• Single-stage Venturi with check valve to halt loss of vacuum from generator in case of air supply failure

Vertical Lifting
Click for Chart

Vertical Lifters for Handling Loads Upright

These are quality, U.S. made vacuum lifters that feature rugged construction and quality components designed to load panels off near-vertical racks and onto other near-vertical tables. They are similar to standard horizontal lifters, but they are designed to handle upright loads. Vertical lifters are designed with a four to one (4 to 1) safety factor on vacuum holding with special non-skid vacuum cups. While these vacuum lifters are priced higher than a horizontal vacuum lifter, they are much less expensive than a powered tilter. Vertical vacuum lifters offer quick attach and release functionality and offer damage-free handling. They can be just the handling tool your factory needs.

To inquire about custom vertical vacuum lifters, please contact an ANVER Sales Engineer for assistance.